EWS 1 Assembly exercises on switching units

EWS 1 Assembly exercises on switching units

These assembly exercises focus on mechanical skills. All exercises are of an extremely practical nature. All parts, except for consumables (wires) can be reused.

 

The following exercises are performed in this course:

  • Familiarization with equipment and various wiring techniques such as flat wiring, channel wiring and chamber wiring.
  • Configuration and commissioning of circuits incorporating these technologies.
  • Contactor control with circuit-breaker
  • Contactor control with inching mode
  • Contactor control with self-holding
  • Contactor control with two operating locations
  • Reversing circuit with contactors
  • Forced sequential connections with main current circuit
  • Interlocking of a contactor control
  • Contactor controls with a timing relay
  • Contactor circuits for motors with 2 speeds and 2 separate windings
  • Dahlander circuit with contactors
  • Star-delta circuit with contactors
  • Starter circuit for a slip-ring motor
Equipment set comprising the following:
1
Installation materials, EWS 1
Installation materials, EWS 1 SE2670-2N
1
Terminal strip set X1
Terminal strip set X1 SE2670-2P
1
Terminal strip set X2
Terminal strip set X2 SE2670-2Q
1
Set of NEOZED fuses
Set of NEOZED fuses SE2670-2S
1
Cable duct (channel) wiring support unit
Cable duct (channel) wiring support unit SE2670-2U
1
Set of fixing materials, cables
Set of fixing materials, cables SE2670-1G
1
Set of wiring materials, EWS 1 (for 8 students)
Set of wiring materials, EWS 1 (for 8 students) SE2670-2R
Media:
1
Manual EWS01 Assembly Practice on Switchgear Circuits (GB)
Manual EWS01 Assembly Practice on Switchgear Circuits (GB) SH5001-3M
Power supply:
1
Mains connection box, 3x400V, three-phase
Mains connection box, 3x400V, three-phase SE2501-1G
Measuring instruments:
1
Voltage, phase + continuity tester with field direction indicator, max. 690V
Voltage, phase + continuity tester with field direction indicator, max. 690V LM8554
1
TRMS digital multimeter MetraHit 2+, CAT III
TRMS digital multimeter MetraHit 2+, CAT III LM2323
Accessories:
3
Storage tray for SE boxes, reinforced, (10 boxes)  310 x 45 x 700 mm
Storage tray for SE boxes, reinforced, (10 boxes) 310 x 45 x 700 mm ST7004-2B
2
Storage tray for installation materials, reinforced base  310 x 700 x 35 mm
Storage tray for installation materials, reinforced base 310 x 700 x 35 mm ST7004-2J
1
Set of fixing materials, punched hole frame
Set of fixing materials, punched hole frame SE2669-3A
1
Set of fixing materials, punched hole frame (100pcs)
Set of fixing materials, punched hole frame (100pcs) SE2669-3C
1
Set of tools ''Electric ''
Set of tools ''Electric '' SE2670-4B
5
Safety measurement cable 4mm, 100 cm, black, 600 V CAT III ~ 1000 V, CAT II / 32 A
Safety measurement cable 4mm, 100 cm, black, 600 V CAT III ~ 1000 V, CAT II / 32 A SO5126-8V
1
Safety measurement cable 4mm, 100cm/40", blue, 600V CAT III ~1000V CAT II / 32A
Safety measurement cable 4mm, 100cm/40", blue, 600V CAT III ~1000V CAT II / 32A SO5126-9A
1
Safety measurement cable 4mm, 100cm/40", gr/ye, 600V CAT III ~1000V CAT II / 32A
Safety measurement cable 4mm, 100cm/40", gr/ye, 600V CAT III ~1000V CAT II / 32A SO5126-9C
1
Mobile aluminum experiment stand, 3 levels, power strip with 6 sockets,(1250 x 1970 x 700 mm)
Mobile aluminum experiment stand, 3 levels, power strip with 6 sockets,(1250 x 1970 x 700 mm) ST7200-4C
1
Punched hole panel, interchangeable, for 1200 mm panel mounting frames
Punched hole panel, interchangeable, for 1200 mm panel mounting frames ST8003-5Q

Alternative mounting solution:

1
Punched hole wiring installation cabin kit, 3 sides + roof, inside 1,26 m x 2,03 m x 1,26 m
Punched hole wiring installation cabin kit, 3 sides + roof, inside 1,26 m x 2,03 m x 1,26 m ST8003-6C
1
Ergo45° 3 HU power duct, 580 mm, for twin wiring installation cabin, horizontal 114 PU
Ergo45° 3 HU power duct, 580 mm, for twin wiring installation cabin, horizontal 114 PU ST8033-3U
1
Full-width front plate (type 1) for six-sided power supply duct 114PU
Full-width front plate (type 1) for six-sided power supply duct 114PU ST8070-4C