"Matrix LED headlights and OLED rearlights" Trainer

This training system offers a practical and target group-oriented introduction to the topic of modern lighting technology. Equipped with two real LED matrix headlights as well as two OLED rear lights, the trainee can understand the structure and function of a modern lighting system in a simple and easy-to-understand way. These lighting elements are connected to a central control interface that enables complete control and operation by the trainee or teacher. In addition to various connections, the interface also accommodates CAN and LIN bus communication, an original light switch, an ignition switch and a mode switch for special light functions.

Learning content

• Basics of measurement technology
• Development of lighting systems
• Conventional lighting systems without bus system
• Conventional lighting systems with CAN bus
• Vehicle networking
• Matrix LED headlamps, design and function
• OLED rear lights, design and function
• Performance of matrix headlamps
• Performance at OLED rear lights
• Adaptive cut-off line
• LIN bus in conventional lighting systems
• Networking of matrix headlamps and OLED rear lamps
• Functional requirements for switching on matrix and OLED tail lights
• Measurement on the CAN bus
• Diagnosis on the CAN bus
• Measurement on the LIN bus
• Diagnosis at the LIN bus
• Diagnosis at matrix headlights
• Diagnosis on OLED rear lights
• Emergency functions of matrix headlamps
• Emergency function of OLED tail lights
• Reading and sending CAN signals from the CAN bus
• Control individual matrix LEDs in the matrix headlamp
• Control 5 light signatures of the OLED rear lights individually by sending messages independently
• Independent programming of switching between wipe flashing and "hard" flashing according to data matrix
• Automatic sequence of different light scenarios
• Automatic high beam on change of speed
• Automatic switching off of Matrix LEDs in case of oncoming traffic 
• Independent programming of matrix LEDs for oncoming traffic and oncoming traffic according to data matrix
• Independent programming of switching elements according to data matrix
• Scope of delivery

The following components are included in the scope of delivery:

• Training system CO3223-2X
• 2 original matrix LED headlamps
• all light elements individually controllable
• each Matrix-LED individually controllable
• Electric headlamp height adjustment
• Error memory clearing
• Headlamp reference run
• Emergency run functions
• programming option for switching between "wipe flashing" and "hard flashing
• Mechanical headlamp adjustment
• 2 original OLED tail lights
• Control of OLED tail lights via "hard" wiring
• Control of OLED tail lights via LIN bus
• 5 different light signatures programmable
• Programming possibility for a change between "wipe flashing" and "hard flashing
• Original light switch
• 3rd brake light
• Ignition switch
• Multiple networked control units
• 4mm safety sockets for signal pick-up and troubleshooting in the lines to the matrix headlights and in the lines to the OLED tail lights
• 4mm safety measurement sockets for signal pick-up on the LIN bus to the light switch
• 4mm safety measuring sockets for signal pick-up at the LIN bus to the gateway
• 4mm safety measuring sockets for signal pick-up, for sending and receiving CAN messages at the gateway

 

• SO2000-2A CAN-LIN Monitor including software CAN-LIN Monitor LN
• Monitoring software for recording CAN and LIN data, graphic display of CAN and LIN data on the PC, transmission of CAN and LIN data. Memory function of several CAN messages, memory function of LIN messages. Individual description of CAN and LIN messages.
• Software Matrix-LED
• Monitoring software for programming switching elements with which the lighting elements are directly controlled. Display of the transmitted data after actuation of the switches, on the PC.
• Interactive e-learning course incl. theory and practical experiments
• Circuit diagrams
• Setpoint list
• Wiring diagrams
• Assignment diagram
• CAN data matrix
• Service work
• Diagnostic work

The following components are additionally required but not necessarily included in the scope of delivery:

• LM2330 Multimeter Multi 13S
• LM6210 oscilloscope

Weight approx. 40 kg

LxWxH 1250x760x1000 mm