IMS 13 Drilling and milling sub-system

IMS 13 Drilling and milling sub-system

A workpiece carrier with the bottom part of a workpiece is placed on the conveyor belt. The drilling and cutting station has a controllable cutting head which reams out the internal contour of the workpiece section. The cutting head can be moved in three axes in order to work on the component. Afterwards the workpiece carrier with its workpiece is moved to the end of the conveyor belt to be passed on to the next sub-system.

Basic equipment set, consisting of: 
1
Drilling and milling station
Drilling and milling station LM9688
1
Double conveyor belt segment, 24V motor
Double conveyor belt segment, 24V motor LM9606
1
Workpiece transport pallet
Workpiece transport pallet LM9620
1
Workpiece, bottom section, white
Workpiece, bottom section, white LM9623
1
Workpiece, bottom section, black
Workpiece, bottom section, black LM9624
Accessories:
1
25-pin serial interface cable, Sub-D plug/socket
25-pin serial interface cable, Sub-D plug/socket LM9061
1
Serial interface cable 9/9 pole
Serial interface cable 9/9 pole LM9040
Media:
1
QuickChart IMS13 - Drilling and milling station
QuickChart IMS13 - Drilling and milling station SO6200-1X
1
Interactive Lab Assistant: IMS 13 Drilling and milling station
Interactive Lab Assistant: IMS 13 Drilling and milling station SO2800-5L
Additionally recommended
1
Compressor, low-noise
Compressor, low-noise SE2902-9L
1
Tubing and accessory set for mechatronics systems
Tubing and accessory set for mechatronics systems LM9670
1
SybaPro mobile IMS experiment trolley with experiment frame, 1200mm, 2 levels
SybaPro mobile IMS experiment trolley with experiment frame, 1200mm, 2 levels ST7200-3T
1
Protective cover for 1200mm wide IMS experiment trolleys with training panel
Protective cover for 1200mm wide IMS experiment trolleys with training panel ST8010-8L

In areas where there are high levels of humidity the membrane dryer

with water trap should be used to avoid...   more

1
IDG3 membrane dryer with rapid coupling and filter AF20 with water trap
IDG3 membrane dryer with rapid coupling and filter AF20 with water trap LM9671
IMS/IPA Tester and Fault Simulator
1
IMS/IPA test and fault simulator
IMS/IPA test and fault simulator CO3713-7V
2
Serial interface cable 9/9 pole
Serial interface cable 9/9 pole LM9040
2
25-pin serial interface cable, Sub-D plug/socket
25-pin serial interface cable, Sub-D plug/socket LM9061
1
QuickChart IMS test and fault simulator
QuickChart IMS test and fault simulator SO6200-1Z
S7-300 PLC control system with accessories:
1
SIMATIC S7-313C 2DP, 16 DI, 16 DO, Profibus, 24 V / 6 A power supply
SIMATIC S7-313C 2DP, 16 DI, 16 DO, Profibus, 24 V / 6 A power supply CO3713-8C
1
IMS interface module for PLC
IMS interface module for PLC CO3713-7F
1
PLC-S7 PC-adapter with USB/MPI converter
PLC-S7 PC-adapter with USB/MPI converter SO3713-5E
Software:
1
Software for training systems 1x STEP 7, S7-Graph, S7-SCL, PLC-Sim(D,GB,F,E,I)
Software for training systems 1x STEP 7, S7-Graph, S7-SCL, PLC-Sim(D,GB,F,E,I) SO6002-1Q
Media:
1
QuickChart, Siemens PLC S7 board, safety instructions
QuickChart, Siemens PLC S7 board, safety instructions SO6200-5A
1
QuickChart, Siemens PLC S7 board, assembly and start-up
QuickChart, Siemens PLC S7 board, assembly and start-up SO6200-5B
1
CLC30, PLC fundamentals, SIMATIC documentation on DVD (D,GB,F,E)
CLC30, PLC fundamentals, SIMATIC documentation on DVD (D,GB,F,E) SO5155-1N
Accessories:
2
Connection plugs for PROFIBUS with PG socket and terminating resistor
Connection plugs for PROFIBUS with PG socket and terminating resistor LM9182
5
Connection cable for PROFIBUS, per metre
Connection cable for PROFIBUS, per metre LM9181
1
Wire stripper for PROFIBUS cables
Wire stripper for PROFIBUS cables LM9184
1
Safety measurement cable (4mm), 100cm/40", blue
Safety measurement cable (4mm), 100cm/40", blue SO5126-9A
1
Safety measurement cable (4mm), 100cm/40", red
Safety measurement cable (4mm), 100cm/40", red SO5126-8U